• 1/4

Hot selling 45# 1045 C45 S45C carbon steel plate

45# steel is widely used in machinery, with high strength, good plasticity and toughness. It is used to make small cross-section quenched and tempered parts with large load and large normalized parts with small stress, as well as surfaces that do not require high core strength. Quenching parts, such as pins, guide posts, watch hands and other components.
Email Us
Contact us
Detail

45# steel is widely used in machinery, with high strength, good plasticity and toughness. It is used to make small cross-section quenched and tempered parts with large load and large normalized parts with small stress, as well as surfaces that do not require high core strength. Quenching parts, such as pins, guide posts, watch hands and other components.

According to GB/T 13304 standard, spring steel is divided into non-alloy spring steel (carbon spring steel) and alloy spring steel according to its chemical composition.


Common Grades:

1. 65, 70, 85 steel grades

High strength, hardness and yield ratio can be obtained, but the hardenability is small, the heat resistance is not good, and the ability to withstand dynamic and fatigue loads is low. It is widely used, but it is mostly used for small springs with low working temperature or less Important larger spring. Such as springs for automobiles, tractors, railway vehicles and general machinery.

The composition of 65Mn is simple, and its hardenability, comprehensive mechanical properties, decarburization and other process properties are better than carbon steel, but it is more sensitive to overheating, has temper brittleness, and is prone to cracks during quenching. The price is low and the amount is large. It can manufacture various small-section flat springs, round springs, springs, etc., as well as valve springs, spring rings, shock absorbers, clutch reeds, brake springs, etc.

2. 55Si2Mn, 60Si2Mn, 60Si2MnA

High silicon content (Wsi) (up to 2.00% upper limit).

High strength and good elasticity. Good anti-tempering stability. Easy to decarburize and graphitize. Hardenability is not high.

The main spring steel type, has a wide range of uses. Manufacture of various springs, such as leaf springs, coil springs for automobiles, locomotives, and tractors, cylinder safety valve springs and some important springs that work under high stress, and springs that are severely worn.

55Si2MnB Due to the boron content, its hardenability is obviously improved. Front and rear suspension springs and auxiliary springs of light and medium-sized automobiles.

55Si2MnB The steel grade developed by China, its hardenability, comprehensive mechanical properties and fatigue properties are better than 60Si2Mn steel. It is mainly used for the manufacture of leaf springs for medium and small cars. .

3. 60Si2CrA 60Si2CrVA

High strength spring steel. High hardenability, good heat treatment process performance. Due to the high strength, the important large springs with large load should be handled in time to eliminate internal stress after coiling the spring. 60Si2CrA can be used to make steam turbine seal springs, regulating springs, condenser support springs, high-pressure water pump disc springs, etc. 60Si2CrVA steel also makes extremely important springs, such as springs for conventional weapons and springs, and springs for breakers.

4. 55CrMnA

The outstanding advantages of 60CrMnA are good hardenability, in addition to hot working properties, comprehensive mechanical properties, anti-decarburization properties, and various important springs with large cross-sections, such as large leaf springs and coil springs for automobiles and locomotives.

5. 60CrMnMoA

It has the highest hardenability among all existing spring steels. Good mechanical properties, anti-tempering stability, etc. Super-large springs used in large-scale civil construction, heavy-duty vehicles, machinery, etc. The thickness of the steel plate can reach more than 35mm, and the diameter of the round steel can exceed 60mm.

6. 50CrVA

A small amount of vanadium improves elasticity, strength, yield ratio and elastic reduction resistance, refines grains, and reduces the tendency of decarburization. The carbon content is small, and the plasticity and toughness are better than other spring steels. High hardenability and good fatigue performance All kinds of important coil springs are especially suitable for springs with high working stress amplitude and strict fatigue performance requirements, such as valve springs, fuel injector springs, cylinder expansion rings, safety valve springs, etc.

7. 60CrMnBA

The hardenability is higher than that of 60CrMnA, and other various properties are similar. Larger size leaf springs, coil springs, torsion springs, etc.

8. 30W4Cr2VA

High strength heat resistant spring steel. Hardenability is good. High temperature relaxation resistance and thermal processing performance are also very good. Heat-resistant springs with working temperature below 500~C, such as steam turbine main steam valve springs, steam seal spring sheets, boiler safety valve springs, 400t boiler disc valve springs, etc.


Mechanical Properties of Typical Chinese Spring Steel Grades


GradeHeat TreatmentMechanical Properties (Not Less Than)
Quenching Temperature(℃)Quenching LiquidTempering Temperature(℃)σ0.2σbδ5δ10Ψ
(kgf/mm2)(%)(%)(%)
65840Oil50080100
935
85820Oil480100115
630
65Mn830Oil54080100
830
60Si2Mn870Oil480120130
525
60Si2CrVA850Oil4101701906
20
50CrMn840Oil490110130
535
55SiMnVB860Oil460125140
530
50CrVA850Oil50011513010
40
30W4Cr2VA1050~1100Oil6001351507
40
GradeHeat TreatmentMechanical Properties (Not Less Than)
Quenching Temperature(℃)Quenching LiquidTempering Temperature(℃)σ0.3σbδ6δ11Ψ
(kgf/mm3)(%)(%)(%)
105860Oil521.3888889143.75158.75
2.73291925536.66666667
125863.3333333Oil526.5555556149.5164.1666667
2.14906832337.66666667
66Mn866.6666667Oil531.7222222155.25169.5833333
1.56521739138.66666667
60Si3Mn870Oil536.8888889161175
0.9813664639.66666667
60Si3CrVA873.3333333Oil542.0555556166.75180.41666679
40.66666667
51CrMn876.6666667Oil547.2222222172.5185.8333333
-0.18633540441.66666667
56SiMnVB880Oil552.3888889178.25191.25
-0.77018633542.66666667
51CrVA883.3333333Oil557.5555556184196.666666710.5
43.66666667
30W4Cr3VA1050~1101Oil562.7222222189.75202.083333311
44.66666667


Overview
Essential details
Standard:
AiSi, ASTM, JIS
Grade:
Q195,Q215,Q235,Q255,Q275,A36, SS400, Q235B
Place of Origin:
Jinan, China
Brand Name:
Tianzhu
Type:
Steel Plate, Checkered Plate
Technique:
Hot Rolled, Cold Rolledor Hot Rolled
Surface Treatment:
Coated
Application:
Ship Plate
Special Use:
High-strength Steel Plate
Width:
1000, 1219, 1500, 1800, 2000mm or as your request
Length:
2440mm,2500mm,5800mm, 6000mm
Tolerance:
±1%
Processing Service:
Bending, Welding, Decoiling, Cutting, Punching
Delivery Time:
7 Days
Product Name:
Hot Rolled Steel Plate
Material:
Q235/Q235B/Q345/Q345B/Q195/St37/St42/St37-2/St35.4/St52.4/St35
Surface:
Black
Usage:
Building Construction Material
Certificate:
ISO9001:2008
Payment term:
30%TT Advance + 70% Balance
Price term:
CIF CFR FOB EXW
Sample:
Sample Freely
Delivery term:
7-14 Workdays

Products Description

Product NameCarbon Steel Sheet
MaterialQ195、Q215、Q235、Q255、Q275,A36, SS400, Q235B,Q345B,Q345C,Q345D,Q345E,Q390,Q390B,Q390C,Q390D,Q390E,Q420,Q420B,Q420C,Q420D,Q420E,Q460,Q460D,Q500C,Q500D,Q500E,Q550C,Q550D,Q550E,Q620C,Q620D,Q620E,Q690A,Q690B,Q690C,Q690D,Q690E,Q690D,Q690C,Q890C,Q890D,16Mo3,16MnL,16MnR,16Mng,16MnDR etc
StandardGB,AISI,ASTM,JIS,DIN,API
Thickness0.1-100mm or as your request
Width1000, 1219, 1500, 1800, 2000mm or as your request
Length2000mm,2440mm(8feet),2500mm,3000mm,3048mm(10feet),5800mm, 6000mm or as your requirements
Treatment/TechniqueHot rolled, cold rolled
SurfacePickled,Black,Polishing,Checkered,Embossed etc
ApplicationsUsed for bridge and construction riveting, bolted and welded structure, as well as general purpose structural steel quality ofcarbon steel, steel plate and bar steel etc
Trade TermsEXW, FOB, CFR, CIF
Delivery timeShipped in 7-15 days after payment
PackageStandard sea-worthy package or as required
SEAWORTHY PACKING20ft GP: 5.8m(length) x 2.13m(width) x 2.18m(high) about 24-26CBM
40ft GP: 11.8m(length) x 2.13m(width) x 2.18m(high) about 54CBM
40ft HG: 11.8m(length) x 2.13m(width) x 2.72m(high) about 68CBM


1.jpgABUIABACGAAg9q_KpQYosKXrdzDuBTieBg.png

ABUIABACGAAg9q_KpQYo8aKowAUw7gU4ogg.png202373ABUIABACGAAgzqeKpQYo8eXl2wIw7gU4kwQ.png


202373202373202373
FAQ

Q1. Where is your factory ?
A1: Our company’s processing center is located in Shandong, China.
Which is well equipped with kinds of machines, such as laser cutting machine,mirror polishing machine and so on.
We can provide a wide range of personalized services according to the customers’ needs.
Q2. What are your company's main products ?
A2: Our main products are carbon steel plate/sheet, coil, round/square pipe, bar, channel, etc.
Q3. How do you control quality ?
A3: Mill Test Certification is supplied with shipment, Third Party Inspection is available.
Q4. What are the advantages of your company ?
A4: We have many professionals, technical personnel, more competitive prices and best after-sales service than other stainless steel companies.
Q5. How many coutries you already exported ?
A5: Exported to more than 50 countries mainly from America, Russia, UK, Kuwait, Egypt, Turkey, Jordan, India, etc.
Q6. Can you provide sample ?
A6: Small samples in store and can provide the samples for free.
Customized samples will take about 5-7days

CONTACT US

  • *
  • *
  • *
  • *
  • *